1.1 --- /dev/null Thu Jan 01 00:00:00 1970 +0000
1.2 +++ b/config/global/paths.in Wed Jun 18 12:54:30 2008 +0000
1.3 @@ -0,0 +1,89 @@
1.4 +# Options related to paths and install
1.5 +
1.6 +comment "Paths"
1.7 +
1.8 +config LOCAL_TARBALLS_DIR
1.9 + string
1.10 + prompt "Local tarballs directory"
1.11 + default ""
1.12 + help
1.13 + If you have previously downloaded the tarballs, enter the PATH where
1.14 + you stored them here.
1.15 +
1.16 +config SAVE_TARBALLS
1.17 + bool
1.18 + prompt "Save new tarballs"
1.19 + default n
1.20 + depends on LOCAL_TARBALLS_DIR != ""
1.21 + help
1.22 + If you say 'y' here, new downloaded tarballs will be saved in the
1.23 + directory you entered above.
1.24 +
1.25 +config PREFIX_DIR
1.26 + string
1.27 + prompt "Prefix directory"
1.28 + default "${HOME}/${CT_TARGET}"
1.29 + help
1.30 + This is the path the toolchain will run from.
1.31 +
1.32 +config INSTALL_DIR
1.33 + string
1.34 +# prompt "Install directory"
1.35 + default "${CT_PREFIX_DIR}"
1.36 +# help
1.37 +# This is the path the target will be installed into.
1.38 +#
1.39 +# Normally, you would set this to ${CT_PREFIX_DIR}, but if for some reasons
1.40 +# you can't write there, you can install somewhere else and have a third
1.41 +# person do the install for you.
1.42 +# The reason you might also want to install elsewhere is if you are going
1.43 +# to package your shinny new toolchain for distribution.
1.44 +
1.45 +config CUSTOM_PATCH
1.46 + bool
1.47 + prompt "Use custom patch directory"
1.48 + default n
1.49 + help
1.50 + If you have custom patches that you want to be applied, say 'Y' here and
1.51 + enter the path directory below.
1.52 +
1.53 + Note that you must ensure that the patch directory is arranged the same
1.54 + way the official directory is.
1.55 +
1.56 +config CUSTOM_PATCH_ONLY
1.57 + bool
1.58 + prompt "Only use custom patches"
1.59 + default n
1.60 + depends on CUSTOM_PATCH
1.61 + help
1.62 + Don't apply patches coming with crosstool-NG, only those patches available
1.63 + in the directory below.
1.64 +
1.65 + If you say 'N' here, then the patches provided with crosstool-NG will be
1.66 + applied first, and then your patches.
1.67 +
1.68 +config CUSTOM_PATCH_DIR
1.69 + string
1.70 + prompt "Custom patch directory"
1.71 + default ""
1.72 + depends on CUSTOM_PATCH
1.73 + help
1.74 + Enter the custom patch directory here.
1.75 +
1.76 +config REMOVE_DOCS
1.77 + bool
1.78 + prompt "Remove documentation"
1.79 + default n
1.80 + help
1.81 + Remove the installed documentation (man and info pages).
1.82 + Gains around 8MiB for a uClibc-based, C and C++ compiler.
1.83 +
1.84 +config INSTALL_DIR_RO
1.85 + bool
1.86 + prompt "Render the toolchain read-only"
1.87 + default n
1.88 + help
1.89 + Render the directory of the toolchain (and its sub-directories)
1.90 + read-only.
1.91 +
1.92 + Usefull for toolchains destined for production.