See http://gcc.gnu.org/PR22541

 From: Dan Kegel

 When building gcc-3.4.3 or gcc-4.x into a clean $PREFIX,

 the configure script happily copies the glibc include files from include to sys-include;

 here's the line from the log file (with $PREFIX instead of the real prefix):

 Copying $PREFIX/i686-unknown-linux-gnu/include to $PREFIX/i686-unknown-linux-gnu/sys-include

 But later, when running fixincludes, it gives the error message

  The directory that should contain system headers does not exist:

   $PREFIX/lib/gcc/i686-unknown-linux-gnu/3.4.3/../../../../i686-unknown-linux-gnu/sys-include

 Nevertheless, it continues building; the header files it installs in

  $PREFIX/lib/gcc/i686-unknown-linux-gnu/3.4.3/include

 do not include the boilerplate that would cause it to #include_next the

 glibc headers in the system header directory.

 Thus the resulting toolchain can't compile the following program:

 #include <limits.h>

 int x = PATH_MAX;

 because its limits.h doesn't include the glibc header.

 The problem is that gcc/Makefile.in assumes that

 it can refer to $PREFIX/i686-unknown-linux-gnu  with the path

                 $PREFIX/lib/../i686-unknown-linux-gnu, but

 that fails because the directory $PREFIX/lib doesn't exist during 'make all';

 it is only created later, during 'make install'.  (Which makes this problem

 confusing, since one only notices the breakage well after 'make install',

 at which point the path configure complained about does exist, and has the

 right stuff in it.)

 A fix that I've been using for a while is to use sed to canonicalize

 the path.  The sed syntax is a bit obtuse, but it works. 

 (hey, that's the first time I've ever used a label in a sed script; thanks to the sed faq

 for explaining the :a ... ta method of looping to repeat a search-and-replace until it doesn't match.)

 [rediffed against gcc-4.1-20060210]

 --- gcc-4.1-20060210/gcc/Makefile.in.old	2006-01-11 06:29:29.000000000 -0800

 +++ gcc-4.1-20060210/gcc/Makefile.in	2006-02-14 16:08:54.000000000 -0800

 @@ -388,7 +388,10 @@

  CROSS_SYSTEM_HEADER_DIR = @CROSS_SYSTEM_HEADER_DIR@

  # autoconf sets SYSTEM_HEADER_DIR to one of the above.

 -SYSTEM_HEADER_DIR = @SYSTEM_HEADER_DIR@

 +# Purge it of unneccessary internal relative paths

 +# to directories that might not exist yet.

 +# The sed idiom for this is to repeat the search-and-replace until it doesn't match, using :a ... ta.

 +SYSTEM_HEADER_DIR = `echo @SYSTEM_HEADER_DIR@ | sed -e :a -e "s,[^/]*/\.\.\/,," -e ta`

  # Control whether to run fixproto and fixincludes.

  STMP_FIXPROTO = @STMP_FIXPROTO@

 @@ -3167,13 +3170,15 @@

  ../$(build_subdir)/fixincludes/fixincl: ; @ :

  # Build fixed copies of system files.

 +# Abort if no system headers available, unless building a crosscompiler.

 +# Canonicalize $gcc_tooldir/sys-include in same way as $SYSTEM_HEADER_DIR was canonicalized so test still works

  stmp-fixinc: gsyslimits.h macro_list \

    $(build_objdir)/fixincludes/fixincl \

    $(build_objdir)/fixincludes/fixinc.sh

  	@if ! $(inhibit_libc) && test ! -d ${SYSTEM_HEADER_DIR}; then \

  	  echo The directory that should contain system headers does not exist: >&2 ; \

  	  echo "  ${SYSTEM_HEADER_DIR}" >&2 ; \

 -	  if test "x${SYSTEM_HEADER_DIR}" = "x${gcc_tooldir}/sys-include"; \

 +	  if test "x${SYSTEM_HEADER_DIR}" = "x`echo "${gcc_tooldir}/sys-include" | sed -e :a -e "s,[^/]*/\.\.\/,," -e ta`"; \

  	  then sleep 1; else exit 1; fi; \

  	fi

  	rm -rf include; mkdir include